- Free shipping on orders over $499*
Pairs well with
The problem this solves
Thick canopy? Big tops? Sad, fluffy lowers?
The 100 watt intercanopy LED is built for one job - driving usable light into the parts of your plant your main fixture can’t reach. When your upper canopy blocks penetration, you lose density down low. That’s wasted space and wasted potential.
This intercanopy LED punches 290 µmol/s of full spectrum light straight through the mid and lower zones, helping hydroponic and commercial growers achieve uniform bud development from top to bottom - not just cola bragging rights.
If you’re chasing consistency across the whole plant, not just the highlight reel, this is where you level up.
🔥 Why growers rate it
Key benefits
• 2.9 µmol/J efficiency → Serious output (290 PPF) without chewing through power
• Full spectrum 3350K → Ideal balance for bloom-stage support and lower bud development
• Designed for intercanopy placement → Targets shaded flower sites your main LED misses
• Link up to 18 bars → Clean daisy-chain setup for large hydroponic or commercial rooms
• IP65 rated housing → Handles humid grow rooms without drama
• Flexible mounting options → Vertical, horizontal, side-mounted - build around your system
• Uniform bloom performance → Improves density and consistency across the entire canopy
This isn’t a replacement for your primary fixture. It’s a performance amplifier for serious flowering rooms.
🛠️ How to dial it in properly
Placement
Install between rows or beneath dense canopy zones where light penetration drops off. Aim to illuminate lower flower sites directly - not blast the underside of leaves for no reason.
Mounting
Run vertically through trellis layers or horizontally along row lines. These bars are multi-orientation friendly, so design around airflow and plant access.
Photoperiod relevance
Best used during bloom alongside your main LED grow lights. They support uniform flower development rather than driving stretch.
Dimming & control
Add the Intercanopy Dimmer for manual control or connect to a compatible ULight controller for automation. Useful if you’re fine-tuning intensity in commercial environments.
Coverage strategy
Daisy-chain up to 18 units per series off one power lead. Plan spacing before install — cable management matters more than people think.
Heat & environment
IP65 rating means it’s built for humid grow rooms and high-density hydroponics setups. Just don’t block airflow around the bars.
Important:
Each series requires one Intercanopy Power Lead (sold separately). Extension Link Cables are needed if spacing bars further apart.
Pro tip
Map your layout on paper before you mount anything. Nothing worse than crawling under a canopy trying to swap cables mid-flower.
🌱 Grow Guys tip
Dense canopy? Lollipopping only gets you so far.
Intercanopy lighting helps convert what would’ve been popcorn into proper, structured flower. Run it alongside your main LED during bloom to tighten up lower sites and boost overall room consistency.
🧩 What it pairs with
This intercanopy LED works best alongside high-output LED grow lights in flowering rooms that already have strong top-down intensity. It’s an add-on strategy, not a standalone solution.
Pair it with quality grow tent kits for controlled environments, or integrate it into commercial grow lighting layouts for multi-tier or high-density hydroponics systems.
You’ll also want proper lighting controllers for automation, and solid air circulation fans to maintain airflow once you start filling out that lower canopy properly.
📦 Technical specs
• Power: 100W
• Efficiency: 2.9 µmol/J
• Total PPF: 290 µmol/s
• Spectrum: Full Spectrum
• CCT: 3350K
• IP Rating: IP65
• Link Capacity: Up to 18 lights per series
• Dimensions: 1100 x 103 x 87mm
• Mounting: Multi-orientation compatible
Compatible accessories (sold separately):
• Intercanopy Power Lead (required – one per series)
• Intercanopy Extension Link Cable (1m)
• Intercanopy Dimmer
• Intercanopy Support Legs (Pair)
❓ Intercanopy LED FAQs
What is an intercanopy LED used for?
An intercanopy LED is designed to light the middle and lower sections of dense plants.
Instead of relying purely on top-down lighting, this 100 watt intercanopy LED pushes usable photons into shaded flower sites. It helps improve uniformity and density across the whole canopy during bloom.
Can I run this as my main grow light?
No - this is a supplemental lighting solution.
It’s built to work alongside your primary LED grow light, especially in flowering rooms with thick canopy development. On its own, it won’t provide full top-down coverage.
How many bars can I connect together?
You can daisy-chain up to 18 bars in one series.
Each series requires one Intercanopy Power Lead, and extension cables if spacing units further apart. Plan your layout before installation to avoid cable headaches later.
Is it safe for humid grow rooms?
Yes - it’s IP65 rated.
That means it’s built to handle humid hydroponic and commercial grow room environments without compromising performance.
🚀 Upgrade your lower canopy performance
If you’re already running a solid flowering setup, this is the smart efficiency play.
Add intercanopy LED support, tighten up lower bud development, and improve yield consistency across your entire room - not just the top layer.
Grab your bars, add the right cables, and build it properly the first time.