VIVOSUN 4-in-1 Sensor VSE-CO2S4, white square sensor with attached cable
VIVOSUN 4-in-1 Sensor hanging above tomato plants in a grow tent, works with GrowHub E42A+
VIVOSUN 4-in-1 Sensor with the light sensor and temperature, humidity, VPD and CO2 sensor labelled
VIVOSUN 4-in-1 Sensor detection ranges with Swiss temperature and humidity chip and NDIR CO2 sensing
VIVOSUN 4-in-1 Sensor linked to a GrowHub E42A+ and inline fan with CO2 readings in the VIVOSUN app
VIVOSUN 4-in-1 Sensor white housing compared with a black housing for heat absorption
VIVOSUN 4-in-1 Sensor use in greenhouses, bedrooms, grow tents and cellars with the GrowHub E42A+
Three steps to calibrate the VIVOSUN 4-in-1 Sensor CO2 reading on the GrowHub E42A+ screen
VIVOSUN 4-in-1 Sensor VSE-CO2S4 specifications, 4.5cm square housing and 3m cable with 2.5mm jack

4-in-1 Sensor by VIVOSUN — CO₂, Temperature, Humidity & Light Sensor for the GrowHub E42A+

VSN-SENSOR-CO2S4

Regular price$84.95
/
Tax included. Shipping calculated at checkout.

Earn 84 points with this purchase

Adds CO₂ and light on/off sensing to the GrowHub E42A+, on top of temperature, humidity and VPD. Plugs into the controller's sensor port. E42A+ only.


  • Handpicked by growers
  • Ships today
  • Real advice, real people
  • 6,759+ high-yielding customers
  • 30-day returns*
  • Free shipping over $499*
  • Low stock - 3 items left
  • Backordered, shipping soon

Pairs well with

Temperature and humidity only tell you half of what the canopy is doing. The 4-in-1 Sensor by VIVOSUN adds CO₂ and light on/off detection to the readings your GrowHub E42A+ already takes, so the controller can see when CO₂ is running low in a closed-up tent, or when a light has not switched when it should. It swaps in for the standard probe on the controller's 2.5mm sensor port, hangs on a 3m cable, and reads CO₂ from 0 to 40,000 ppm with an NDIR sensor. It suits growers already running an E42A+ who want CO₂ on the screen and in their fan or CO₂ triggers. The honest limits: it works with the E42A+ only, the light reading is on or off and not a PAR or lux figure, and it measures CO₂ without adding any.

E42A+ only. This sensor plugs into the GrowHub E42A+ and takes the place of its standard temperature and humidity probe. It does not work with the GrowHub E42 or E42A.
CO₂ on the controller screenAn NDIR sensor reads CO₂ from 0 to 40,000 ppm and sends it to the E42A+, where you can set triggers for your exhaust fan or CO₂ equipment.
Confirms the light actually switchedLight detection reports on or off, so you can check whether the tent went dark or lit up on schedule. It is not a PAR or lux reading.
Replaces the probe, no extra portsIt plugs into the same 2.5mm sensor port as the standard E42A+ probe and carries temperature, humidity, CO₂ and light down one cable.
Swiss temperature and humidity chipTemperature to ±0.8°C and humidity to ±6% RH feed the controller's VPD reading, so your fan triggers work from canopy conditions.
Made to hang at the canopyA 3m cable reaches from the controller to the plants, and the white housing is there to reduce heat absorption under the light.
Calibrate it from the controllerCO₂ calibration runs from the E42A+ itself in a few minutes, so you can keep the reading honest month to month.

Specifications

Brand: VIVOSUN
Model: VSE-CO2S4
Measures: Temperature, humidity, CO₂ and light on/off
Compatible controller: GrowHub E42A+ only
CO₂ sensor: NDIR
CO₂ range: 0–40,000 ppm
CO₂ accuracy: 50 ppm ±5%
Temperature range: -10 to 60°C
Temperature accuracy: ±0.8°C
Humidity range: 0–100% RH
Humidity accuracy: ±6% RH
Light detection: On/off only
Response time: Temperature and humidity 200ms, CO₂ 60s, light 120ms
Operating humidity: Up to 90% RH
Interface: 2.5mm jack
Cable length: 3m (118in)
Dimensions: 45 × 45 × 13.5mm
In the box: 1 × 4-in-1 sensor with attached cable
Warranty: 2 years (manufacturer)

Grower's Tip

  • Hang it about 10cm above the canopy, which is where VIVOSUN's manual puts it, and lift it as the plants grow.
  • Keep it out of the direct airstream of your fans and away from any CO₂ outlet, so it reads the air the plants are sitting in.
  • Calibrate the CO₂ reading once a month. VIVOSUN's method is to take the sensor outdoors to a well-ventilated spot, let it settle for 3 minutes, then run CO₂ calibration from the controller.
  • VIVOSUN's manual lists reference CO₂ levels of 400 ppm at germination, 600 for seedlings, 800 in veg and 1000 in flower. Treat them as a starting point: the right level is plant-specific and depends on your light and temperature.
  • The light reading only tells you on or off. To measure intensity at the canopy you still need a PAR meter.
  • Keep it dry. VIVOSUN rates it for up to 90% RH and warns against excessive moisture, so move it out of the way before foliar spraying.

How To Set It Up

1Check your controller is the GrowHub E42A+ (model GH-E42AP). The sensor does not work with the E42 or E42A.
2Unplug the standard temperature and humidity probe from the controller's 2.5mm sensor port and plug the 4-in-1 Sensor in its place.
3Run the cable into the tent and hang the sensor about 10cm above the canopy, clear of fan airflow.
4Calibrate CO₂ before you rely on it: take the sensor outdoors to a well-ventilated spot, let it settle for 3 minutes, then run CO₂ calibration from the E42A+.
5Check temperature, humidity, CO₂ and light status are all showing on the controller and in the VIVOSUN app.
6Set your triggers on the E42A+ for the fan or CO₂ equipment you run, watch a full day and night, then fine-tune. Repeat the calibration monthly.

Pairs Well With

Frequently Asked Questions

Does it work with the GrowHub E42 or E42A?

No. VIVOSUN lists the GrowHub E42A+ as the only compatible controller. If you are not sure which one you have, the E42A+ has a 4.3" colour screen and the model number GH-E42AP.

Does it replace the probe that came with my E42A+?

Yes. It uses the same 2.5mm sensor port, so the standard probe comes out and this goes in. You keep temperature and humidity and gain CO₂ and light detection.

Does it measure light intensity?

No. It detects whether the light is on or off. It does not give a PAR, PPFD or lux figure, so use a PAR meter to set light height and dimming.

Does it add CO₂ to the tent?

No. It measures CO₂ and reports it to the controller. Raising CO₂ takes a separate CO₂ source, and lowering it takes fresh air from your exhaust fan.

Do I need to calibrate it?

Yes. VIVOSUN recommends calibrating CO₂ once a month: take the sensor outdoors to a well-ventilated spot, let it settle for 3 minutes, then run CO₂ calibration from the E42A+ controller.

Is it waterproof?

No. VIVOSUN's manual warns against excessive moisture and rates it for operation up to 90% RH. Keep it clear of misting and foliar sprays.

How accurate is it?

VIVOSUN's published figures are ±0.8°C for temperature, ±6% RH for humidity and 50 ppm ±5% for CO₂.

Does it come with a warranty?

Yes. It carries VIVOSUN's 2-year manufacturer warranty.

See CO₂ At The Canopy

Add CO₂ and light sensing to your GrowHub E42A+. Free shipping over $499*.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.

Growers First, Retailers Second

Welcome to The Grow Guys

We built The Grow Guys from the soil up — well, coco and perlite. Before we sold gear, we bought it, ran it, and learned the hard way what's worth the money and what ends up in the shed. That's the filter everything on our shelves passes through. No sales scripts, no rebadged junk, no telling you what you want to hear. Just gear we'd run ourselves and advice from people who actually grow. Chasing higher yields, tighter flowers, or your first harvest? You're in the right place.

Meet The Grow Guys

FAQs

How fast do you ship?

Order by 2pm and it ships the same business day from Invermay, Tasmania.

How much is shipping?

Calculated at checkout by weight and destination. Free shipping over $499*.

Is the packaging discreet?

Plain packaging, no branding. No one knows what's in your box.

What's your returns policy?

30-day change-of-mind returns on unopened, unused products. A 10% restocking fee applies and return shipping is at your cost.

Can I get advice before buying?

Call, email, or walk into the Invermay shop. You'll get a grower on the other end, not a script.

Do you have a physical store?

Unit 10/110 Gleadow Street, Invermay 7248. Mon–Fri 8:30am–5:30pm, Sat 9am–3pm.

Inside The Grow Guys hydroponics store in Invermay, Tasmania

Still got a question?

Talk to a grower, not a script

Tell us your space and what you want to grow. We'll point you to the gear that fits, and tell you what you can skip.

Call 0481 735 126

Mon–Fri 8:30am–5:30pm · Sat 9am–3pm

You may also like


Recently viewed